HYS Hybrid Strut
Deflection Connectors
This product's information may differ depending on the category of use. You are currently viewing details related to Deflection Connectors. You can also view product information related to the category: Rigid Connectors for Cold-Formed Steel Construction
Product Details
The HYS hybrid strut is the only CFS strut on the market designed and tested for use as either a slide or a rigid clip. Commonly used at the bottom of a steel beam to accommodate large standoff conditions, the HYS strut attaches to the structure with screws, powder-actuated fasteners or welds.
The HYS has undergone comprehensive component, assembly and anchor testing. Tabulated loads were developed from these tests and include capacities based on strength and deflection to assist in mitigating design risk. You can count on the HYS dual-application strut for its versatility and test-verified performance.
Key Features
- Available in lengths of 12", 15", 24" and 30" (for 18" lengths, use SSB and FSB struts)
- Slots are positioned to minimize eccentric load and maximize capacity
- Slide application allows up to 1" of vertical moment in each direction when shouldered screws are used through the center of the slot
- Simpson Strong-Tie® No-Equal® stamps mark the center of the slots to help ensure correct placement of shouldered screws
- Supports gravity and lateral loads when using #10 screws through small predrilled holes
Material
- HYS12/68, HYS15/68, HYS24 /68 — 68 mil (14 ga.), 50 ksi HYS30/97 — 97 mil (12 ga.), 40 ksi
Finish
- Galvanized (G90)
Installation
- For installation as a slide connection, attach the HYS using shouldered screws through the slotted holes. Precision-manufactured shouldered screws provided with the HYS are designed to prevent over-driving and to ensure that the clip functions properly in the slide application. For installation as a rigid connection to support gravity and lateral loading, attach the clip using the small predrilled holes with #10 screws.
Related Literature
Product Information Table
| Model No. | Thickness (mil) | Ga. | L (in.) | Product Includes | Coating/Material | Packaging Qty. |
|---|---|---|---|---|---|---|
| HYS12/68-KT25 | 68 | 14 | 12 | (25) connectors; (83) XLSH78B1414 #14 shouldered screws | Zinc Galvanized, G90 | 25 |
| HYS15/68-KT25 | 68 | 14 | 15 | (25) connectors; (83) XLSH78B1414 #14 shouldered screws | Zinc Galvanized, G90 | 25 |
| HYS24/68-KT15 | 68 | 14 | 24 | (15) connectors; (55) XLSH78B1414 #14 shouldered screws | Zinc Galvanized, G90 | 15 |
| HYS30/97-KT10 | 97 | 12 | 30 | (10) connectors; (55) XLSH78B1414 #14 shouldered screws | Zinc Galvanized, G90 | 10 |
Load Tables
HYS Slide-Clip Allowable Loads (lb.)
- For additional important information, see General Notes.
- HYS Allowable Connector Loads are also limited by the HYS Anchorage Load table. Use the minimum tabulated values from the connector and anchorage load tables as applicable.
- See illustrations on the side for fastener placement to stud framing.
- Tabulated F1 loads are based on assembly tests with the load through the centerline of the stud. Tests are governed by fastener connections.
Typical HYS (Slide-Clip Application)
Slide Screw Pattern S1
(no screws required in small round holes in slide application)
(no screws required in small round holes in slide application)
Slide Screw Pattern S2
(no screws required in small round holes in slide application)
(no screws required in small round holes in slide application)
HYS Fixed-Clip Allowable Loads (lb.)
- For additional important information, see General Notes
- HYS Allowable Connector Loads are also limited by the HYS Anchorage Load table. Use the minimum tabulated values from the connector and anchorage load tables as applicable.
- See illustrations on the side for screw fastener placement to stud framing.
- Tabulated F1 loads are based on assembly tests with the load through the centerline of the stud. Tests are governed by fastener connections.
- XLSH78B1414 #14 shouldered screw may be used to replace #10 screws in a fixed application.
- Minimum stud width for fixed application is 6".
Typical HYS (Fixed-Clip Application)
Fixed Screw Pattern R1
(no screws required in slot in fixed application)
(no screws required in slot in fixed application)
Fixed Screw Pattern R2
(no screws required in slot in fixed application)
(no screws required in slot in fixed application)
HYS Allowable Anchorage Loads (lb.)
- For additional important information, see General Notes.
- Allowable loads are for the clip anchorage only. The capacity of the connection system will be the minimum of the tabulated value and the allowable load from the HYS Allowable Connector Loads above for slide applications and fixed applications.
HYS Maximum Standoff Distances (in.)
Code Reports & Compliance
Drawings
| DWG | DXF | RFA | IFC | SAT | |||
|---|---|---|---|---|---|---|---|
