DU™ Face-Mount Fire Wall Hanger
Fire Wall Hangers for Plated Truss
This product's information may differ depending on the category of use. You are currently viewing details related to Fire Wall Hangers for Plated Truss. You can also view product information related to the categories of: Fire Wall Hangers for Solid Sawn Lumber, Fire Wall Hangers for Engineered Wood
Product Details
Engineered and tested to perform, Simpson Strong-Tie® hangers are manufactured to the highest quality standards for structural strength and safety. The DU face-mount hanger is designed for lighter use to carry joist floor loads to a wood stud wall over two layers of 5/8" gypsum board (drywall). The DU hanger installs after the drywall is in place.
Key Features
- Testing verifies that the DU hangers do not reduce the two-hour fire wall assembly rating in either 2x4 or 2x6 walls.
- DU fire wall hangers are code listed for structural use under ICC-ES ESR-2552.
- Hangers have been tested according to ASTM E814 and received F (flame) and T (temperature) ratings for use on one or both sides of the wall in Intertek Design No. SST/WPCF 120-01. If hangers are installed on both sides of the wall, then it must be a 2x6 wall.
Material
- 14 gauge
Finish
- Galvanized
Installation
- Use all specified fasteners; see General Notes.
- Strong-Drive® SDS Heavy-Duty Connector screws are provided with the hanger.
- Drywall is installed first.
- Mounted with top of hanger flush with top of wall and tight to the drywall.
- Wall top plates must be restrained to prevent rotation. Where gravity load on top of wall is less than 150 plf, use a stud-plate tie connector at the back of each stud or provide equivalent restraint by another method as determined by designer.
- Upper plate splices must occur at a stud location.
Related Literature
Product Information Table
| Model No. | Joist Size | Ga. | W (in.) | H (in.) | B (in.) | Coating/Material | Product Includes | Packaging Qty. |
|---|---|---|---|---|---|---|---|---|
| DU1.81/11.88 | 1-3/4 in. x 11-7/8 in. | 14 | 1 13/16 | 11 13/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU1.81/14 | 1-3/4 in. x 14 in. | 14 | 1 13/16 | 13 15/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU1.81/9.5 | 1-3/4 in. x 9-1/2 in. | 14 | 1 13/16 | 9 7/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU2.1/11.88 | 2 to 2-1/16 in. x 11-7/8 in. | 14 | 2 1/8 | 11 13/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU2.1/14 | 2 to 2-1/16 in. x 14 in. | 14 | 2 1/8 | 13 15/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU2.1/9.5 | 2 to 2-1/16 in. x 9-1/2 in. | 14 | 2 1/8 | 9 7/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU2.37/11.88 | 2-5/16 in. x 11-7/8 in. | 14 | 2 3/8 | 11 13/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU2.37/14 | 2-5/16 in. x 14 in. | 14 | 2 3/8 | 13 15/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU2.37/16 | 2-5/16 in. x 16 in. | 14 | 2 3/8 | 15 15/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU2.37/9.5 | 2-5/16 in. x 9-1/2 in. | 14 | 2 3/8 | 9 7/16 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU210 | 2x10 | 14 | 1 9/16 | 9 1/8 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
| DU212 | 2x12 | 14 | 1 9/16 | 11 1/8 | 2 | Zinc Galvanized, G90 | (4) 1/4 in. x 3-1/2 in. Strong Drive SDS Heavy-Duty Connector screws | 1 |
Product Information Tables
Load Tables
- Loads assume 5/8" Type X drywall attached per IBC. Wall assembly must consist at a minimum of two 2x4 plate members with studs spaced not more than 16" o.c. For alternative solutions to mounting over a single layer of drywall, refer to the technical bulletin T-C-TFWALL.
- Hangers spaced closer than 16" o.c. shall reduce allowable load proportionately.
- Triangular nail holes may be filled with (4) additional 0.148" x 1 1/2" to achieve an allowable upliftl load of 750 lb.
- DF carried members with a minimum of 1 1/2" x 2 1/2" solid sawn chord dimensions may increase Allowable Uplift Load to 170 lb.
- For a DU two-sided (back-to-back) application on a 2x6 wall, use 1,075 lb. allowable download for DF/SP plates and 880 lb. for SPF/HF plates.
- For the DU, if a 5/8" structural wood panel is used between the drywall and the studs, use 1,110 lb. allowable download for DF/SP plates and 880 lb. for SPF/HF plates.
Fastener Table
Code Reports & Compliance
Drawings
| DWG | DXF | RFA | IFC | SAT | |||
|---|---|---|---|---|---|---|---|
