LCE Light Post Cap for End Condition
Misc. Connectors
This product's information may differ depending on the category of use. You are currently viewing details related to Misc. Connectors. You can also view product information related to the category: Two-Piece Post Caps
Product Details
The LCE is designed to provide a connection when the end of a beam bears on a post. The versatile, two-piece design of this light post cap for end conditions can accommodate 4x and 6x lumber. The LCE is ideal for both new and retrofit construction and is load rated when installed in pairs.
Key Features
- Always install in pairs; universal design eliminates need for rights and lefts
- Stronger than angled nailing or screw fastening
- Eliminates nailing into end grain
- Tested and approved for mitered end conditions
Material
- LCE4 — 20 ga. (33 mil)
Finish
- Galvanized, ZMAX® coating or stainless steel; see Corrosion Information
Installation
- Use all specified fasteners; see General Notes
- Install all models in pairs to achieve allowable loads
- Install one LCE4 on each outside face for mitered corners
Related Literature
Product Information Table
| Model No. | Ga. | L (in.) | Coating/Material | Packaging Qty. |
|---|---|---|---|---|
| LCE4 | 20 | 5 3/8 | Zinc Galvanized, G90 | 1 |
| LCE4SS | 20 | 5 3/8 | Stainless Steel | 1 |
| LCE4Z | 20 | 5 3/8 | ZMAX® | 1 |
Load Tables
For stainless-steel fasteners, see Fastener Types and Sizes Specified for Simpson Strong-Tie Connectors.
Many of these products are approved for installation with Strong-Drive® SD Connector screws.
- Allowable loads have been increased for wind or earthquake loading with no further increase allowed. Reduce where other loads govern.
- Connector table loads and fastener quantities are listed for two parts.
- Lateral load is in the direction parallel to the beam.
- For minimum nailing quantity and load values, fill all round holes; for maximum nailing quantity and load values, fill all round and triangular holes.
- LCE4 uplift load for mitered-corner conditions is 985 lb. (DF/SP) or 845 lb. (SPF). Lateral loads do not apply.
- Structural composite lumber columns have sides that show either the wide face or the edges of the lumber strands/veneers known as the narrow face. Values in the tables reflect installation into the wide face. See technical bulletin T-C-SCLCLM for load reductions resulting from narrow-face installations.
- Fasteners: Nail dimensions in the table are listed diameter by length. For additional information, see Fastener Types and Sizes Specified for Simpson Strong-Tie Connectors.
- The allowable download for the mitered LCE4Z connection is limited to the bearing of the mitered beams on the post and shall be determined by the designer.
- The combined uplift loads applied to all the beams must not exceed the post allowable uplift load listed in the table.
- Connectors must be installed in pairs to achieve listed loads.
- Fasteners: Nail dimensions in the table are listed diameter by length. For additional information, see Fastener Types and Sizes Specified for Simpson Strong-Tie Connectors.
Load Values with Strong-Drive® SD Connector Screws
| Model No. | Nominal Post Size | Fasteners | Allowable Loads | |||
|---|---|---|---|---|---|---|
| Beam Flange | Post Flange | Uplift | Lateral F1 | |||
|
These products are available with additional corrosion protection. Additional products on this page may also be available with this option, check with Simpson Strong-Tie for details.
|
||||||
| LCE41 | - | 14-SD10112 | 10-SD10112 | 1860 | 1355 | |
Code Reports & Compliance
Drawings
| DWG | DXF | RFA | IFC | SAT | |||
|---|---|---|---|---|---|---|---|
