HGLT Heavy Glulam Top-Flange Hanger
Product Details
The HGLT is designed to accommodate typical structural requirements for glulam beams. The Funnel Flange™ feature of this top-flange hanger allows for easy installation of beams. The HGLT installs with heavy N54 ring-shank nails specifically created for glulam or heavy timber.
Key Features
- N54 ring-shank nails included
- Easy installation with Funnel Flange
- Not acceptable for nailer applications
Material
- 3 ga. top flange; 7 ga. stirrup
Finish
- Simpson Strong-Tie gray paint. Hot-dip galvanized is available; specify HDG.
Installation
- Use all specified fasteners. Verify that the header can take the required fasteners specified in the table.
- For attaching to multi-ply headers, refer to technical bulletin Top-Flange Hanger Reductions for Multiple-Ply Headers (T-C-MPLYHEADR).
- Flatten edge of header to match top-flange radius.
- Bevel-cut the carried beam for skewed hangers.
- For hangers exceeding the joist height by more than 1/2", allowable load is 50% of the table load.
- May be used for weld-on applications. Minimum required weld is a 1/4" x 2 1/2" fillet weld at each end of the top flange; see General Instructions for the Installer, note k, for weld information. Weld-on applications produce maximum loads listed. For uplift loads, refer to technical bulletin Top-Flange Hangers Welded to Structural Steel Members (T-C-WELDUPLFT).
- N54A nails are included. N54A nails should only be used with solid sawn, timber or glulam headers. When installing on structural composite lumber, use 1/4" × 2 1/2" Strong-Drive® SDS Heavy-Duty Connector screw in lieu of the N54A nails. Consider HGLTV as an alternative when used with SCL.
Options
- Hot-dip galvanized; specify HDG.
- Seats may be skewed to a maximum of 50° and/or sloped to a maximum of 45°.
- When seat is sloped, the maximum allowable load is 9,165 lb.
- When seat is skewed, the maximum allowable load is 7,980 lb. The deflection at full loading may reach 1/4". For skews greater than 15°, multiply the table uplift load by 0.50.
- For sloped and skewed seat combinations, the maximum allowable load is 9,650. The deflection at full loading may reach 1/4". For skews greater than 15°, multiply the table uplift load by 0.50.
- Sloped or skewed seat hangers may not be installed in non-backed nailer/header installations.
- Top flange may be sloped down to the left or right as far as 30°. Reduce allowable loads using the following reduction factor based on linear interpolation: (90–α)/90, where α is the angle measure from the horizontal. This reduction is not cumulative with other load reductions.
- Top flange may be offset left or right for placement at the end of a header. Minimum seat width is 3 1/4". The maximum allowable load is 0.45. No uplift load is available. Offset top flange and sloped seat is allowed with 0.45 load factor.
- For skewed and offset or skewed only top-flange hangers with inward or outward configuration, the maximum allowable load is the lesser of (a) 45% of the catalog load or (b) 4,300 lb.
Related Literature
Product Information Table
Load Tables
| Model No. | Joist (in.) | Fasteners (in.) | Allowable Loads Header Type | ||||
|---|---|---|---|---|---|---|---|
| Width | Height | Top | Face | Joist | Uplift (160) | DF/SP | |
| HGLT Series | 3 1/8 — 8 3/4 | 7 1/2 — 33 | (6) N54A | (12) N54A | (6) N54A | 2,450 | 10,720 |
- Uplift loads have been increased for earthquake or wind loading with no further increase allowed. Reduce where other loads govern.
- Uplift loads apply only when "H" is 28" or less.
- For hanger heights exceeding the joist height, the allowable load is 0.50 of the table load.
- For SCL products made primarily from Douglas fir or Southern pine, use 1,640 lb. for uplift. For SPF members, use 1,115 lb. for uplift.
- Fasteners: Nail dimensions in the table are listed diameter by length. For additional information, see Fastener Types and Sizes Specified for Simpson Strong-Tie Connectors.
Code Reports & Compliance
Drawings
| DWG | DXF | RFA | IFC | SAT | |||
|---|---|---|---|---|---|---|---|
